Digital control of an electro discharge machining (EDM) system

Digital control of an electro discharge machining (EDM) system

This thesis presents a model of the complete Electro Discharge Machining (EDM) system and the design and implementation of a digital controller for the servomotor control and the gap voltage and current pulse power generator. A Matlab/Simulink simulation is used to investigate the EDM system model b...

Full description

Bibliographic Details
Main Author:	Yahya, Azli
Published:	Loughborough University 2005
Subjects:	629.8043
Online Access:	http://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.429020

Similar Items

Robust anti-windup control and its application to permanent magnet synchronous motor speed regulation
by: March, Philip
Published: (2009)

Planning and organizational abilities in patients with frontal lobe neurosurgery investigated using virtual reality
by: Kotitsa, Maria
Published: (2005)

The release and actions of the neurophysical hormones
by: Hartley, David Edward
Published: (2003)

Holocaust memory for the Millennium
by: Allwork, Larissa Faye
Published: (2011)

Konstruksjonsanalyse av bjelke-/platebruer av betong : Effekter av horisontalkurvatur, forspenning og trafikklast
by: Lunde, Mads, et al.
Published: (2012)

Computer aided analysis and design of a new servo control feed drive for electro discharge machining using piezoelectric ultrasonic motor
by: Shafik Hassan Abd Alla, Mahmoud
Published: (2003)

Ultrasonic Vibration Assisted Electro-Discharge Machining (EDM)—An Overview
by: Nurbol Sabyrov, et al.
Published: (2019-02-01)

MEMS-enabled micro-electro-discharge machining (M³EDM)
by: Alla Chaitanya, Chakravarty Reddy
Published: (2009)

MEMS-enabled micro-electro-discharge machining (M³EDM)
by: Alla Chaitanya, Chakravarty Reddy
Published: (2009)

MEMS-enabled micro-electro-discharge machining (M³EDM)
by: Alla Chaitanya, Chakravarty Reddy
Published: (2009)

Digital control techniques for electro-hydraulic servosystems
by: Plummer, Andrew Robert
Published: (1991)

Investigation for improvement and application of MEMS-based micro-electro-discharge machining (M3EDM)
by: Wang, Ningyuan
Published: (2011)

Investigation for improvement and application of MEMS-based micro-electro-discharge machining (M3EDM)
by: Wang, Ningyuan
Published: (2011)

Investigation for improvement and application of MEMS-based micro-electro-discharge machining (M3EDM)
by: Wang, Ningyuan
Published: (2011)

Electro-active polymer (EAP) dimple actuators for flow control
by: Dearing, Stella
Published: (2008)

General simulation and design tools for control of electro-mechanical systems
by: Atyia, Thamir Hassan
Published: (2000)

Electrical Discharge Machining (EDM): A Review
by: Asfana Banu, et al.
Published: (2016-09-01)

Micro Machining Using Micro-EDM Combined with Electro-codeposition
by: Wei-Chieh Wu, et al.
Published: (2006)

Electro-mechanical interactions in aerospace gas turbines
by: Moore, Gareth Edward
Published: (2013)

Modelling and optimisation of Electro-Active Polymer (EAP) devices
by: Rosenblatt-Weinberg, Florence
Published: (2013)

Computer control of a paper machine
by: Hem, S.
Published: (1969)

Effect of machining polarity on single discharge characteristics in micro-EDM
by: Wang Kan, et al.
Published: (2020-01-01)

Fault tolerance in rotorcraft digital flight control systems
by: Elphick, Jonathan Richard
Published: (1996)

Partial discharges under non-standard conditions
by: Al-Rumayan, Faisal
Published: (2008)

Implementaion of EDM Discharging Controller By Using VLSI
by: Ching-Chang Cheng, et al.
Published: (1994)

Mathematical model of electrical discharge machining pulse profile
by: Ahmad, Adibah, et al.
Published: (2018)

Influence of Work and Tool Materials on Parameters of Electrical Discharge Machining (Edm)
by: A.K.M.N. Amin A.K.M.N. Amin, et al.
Published: (2012-08-01)

PERFORMANCE OF ELECTRICAL DISCHARGE MACHINING (EDM) WITH NICKEL ADDED DIELECTRIC FLUID
by: AHSAN ALI KHAN, et al.
Published: (2018-06-01)

Modeling and optimization of Electrical Discharge Machining (EDM) using statistical design
by: Hegab Husein A., et al.
Published: (2015-01-01)

Digital control using field programmable gate arrays
by: Niu, Jianyong
Published: (2006)

Computer aided identification and design for direct digital control
by: Bates, M.
Published: (1979)

Discharge physics and associated phenomena in an ion thruster type hollow cathode
by: Patterson, Stephen William
Published: (2004)

The Design of EDM Discharge Pulse Control and Monitoring Module
by: Fu, Chien-Chung, et al.
Published: (1996)

EDM DISCHARGE WAVEFORM IDENTIFICATION AND FUZZY CONTROL DESIGN
by: Chuei-Ya Peng, et al.
Published: (1994)

Consistent machining of electrical discharge machining power supply towards hip implant surface texturing
by: Mahmud, Nazriah, et al.
Published: (2018)

Dynamic modelling and control of a two-wheeled robotic machine with an extended rod
by: Goher, Khaled M. K.
Published: (2010)

Low speed encoderless control of permanent magnet AC machines for automotive applications
by: Curson, Adam Stefan
Published: (2010)

Alternative methods for determining coefficients of discharge for engine simulation
by: Gault, R. I.
Published: (2003)

Electro discharge machining for micro manufacturing
by: Ivanov, Atanas
Published: (2008)

Influence of Machining Parameters and Assistant Magnetic Force on Discharge Waveform using EDM
by: Yung-sheng Chen, et al.
Published: (2005)

Cannot write session to /tmp/vufind_sessions/sess_7sbt0150c4ssn682a4e3kipskj