An investigation into below centre centreless grinding

An investigation into below centre centreless grinding

Bibliographic Details
Main Author:	Johnson, S. P.
Published:	Coventry University 1989
Subjects:	621.8 Grinding machine stability
Online Access:	http://ethos.bl.uk/OrderDetails.do?uin=uk.bl.ethos.234797

Similar Items

Investigation of in-process dressing in creep feed grinding
by: Rezaei, M.
Published: (1987)

High-rate grinding wheel design
by: Barlow, N.
Published: (1988)

Grinding of advanced ceramic materials : experimental and theoretical investigation into crack initiation and propagation
by: Abdul-Wahab Mokbel, Amin
Published: (1997)

The effect of grinding wheel flexibility on chatter performance
by: Baylis, R. J.
Published: (1984)

Investigation of the problems of buried thin-wall pipes
by: Cray, P. A.
Published: (1974)

Investigations into an adjustable fluid film bearing
by: Martin, J. K.
Published: (1997)

An investigation into vibration criteria for rotating machinery
by: Woods, R.
Published: (1968)

An investigation into tribological and performance related aspects polymeric gearing
by: Dearn, Karl David
Published: (2009)

Investigation of novel variable flux reluctance machine characteristics
by: Liu, Xu
Published: (2013)

An investigation into the fundamentals of microslip and wear in rolling contact bearings
by: Bremble, G. R.
Published: (1969)

An investigation into the operation of water-lubricated rubber journal bearings
by: Cabrera, D. L.
Published: (2003)

An investigation of high speed and power permanent magnet synchronous machines
by: Mehna, Ali A. Ahmed Omran
Published: (2011)

Experimental investigation into the influence of roughness on friction and film thickness in EHD contacts
by: Guegan, Johan
Published: (2015)

Compaction simulator performance analysis
by: Okapala, Chukwuemeka J.
Published: (1997)

The flexibility of piping systems : an experimental investigation of the stresses and end reactions in full-scale piping systems caused by thermal expansion and other movements
by: Smith, Raymond Thomas
Published: (1965)

Vibration control in rotating machinery using variable dynamic stiffness hydrostatic squeeze-films
by: Roach, M. P.
Published: (1990)

The influence of machine thermal design and operating conditions on scuffing failure
by: Finnis, Melanie P.
Published: (1989)

The design of a lathe attachment for grinding non-circular cross- section shafts suitable for torque transmission
by: Taylor, Brian
Published: (1987)

The normal dynamic characteristics of machine tool plain slideways
by: Dolbey, M. P.
Published: (1969)

Plastic injection moulding machine controllers
by: Farrar, P. T. K.
Published: (1987)

The wear behaviour of pearlitic steels with particular reference to rails
by: Clayton, P.
Published: (1977)

Infra-red surface temparature measurements in lubrication
by: Jeffs, P. T.
Published: (1978)

Study of parameters influencing surface distress of gears
by: Alanou, M. P.
Published: (2006)

A study of the mechanics of the two thread chainstitch machine and the geometrical properties of the two thread chainstitch seam
by: Jones, Rowland R.
Published: (1980)

The design of fixture supports to prevent surface attitude changes at the point of tool load
by: Nixon, James
Published: (1991)

Studies in and modelling of a multi-product manufacturing system to aid the selection and financial appraisal of advanced machine tools
by: Kilmartin, B. R.
Published: (1983)

The interactive three dimensional computer aided design of industrial circular weft knitting machines
by: Simms, G. J.
Published: (1981)

MDI data preparation for numerically controlled milling machines
by: De Queiroz, Abelardo Alves
Published: (1983)

Development of a microprocessor-based signal analyser for machine condition monitoring
by: MacLean, Colin S.
Published: (1984)

Numerical modelling of through-thickness reinforced structural joints
by: Bianchi, Francesco
Published: (2012)

Sensorless control strategies for low-cost, high-speed electrical drive systems
by: Bateman, Christopher John
Published: (2010)

The performance of dry running non-metallic gears
by: Mao, Kun
Published: (1993)

Development of an optimum pipeline renovation using Cured-In-Place Pipe (CIPP) techniques
by: Razmara, Mohammad
Published: (2008)

Tribology of polymers and composites in unlubricated rolling and sliding contact
by: Chen, Yong Kang
Published: (1996)

Condition monitoring and fault diagnosis of three-phase induction motors
by: Liang, Bo
Published: (2001)

Constraint analysis and theoretical development of multi-furcation and reconfiguration in mechanisms
by: Qin, Yun
Published: (2013)

Prediction of contact fatigue for the rough surface elastohydrodynamic lubrication line contact problem under rolling and sliding conditions
by: Qiao, Hua
Published: (2005)

Impulsive vibration measurement for rolling bearing condition assessment
by: Birch, David James
Published: (2002)

A generalised approach to machine control
by: Harrison, Robert
Published: (1991)

Optimisation of a high-energy loss control valve trim using computational and experimental techniques
by: Morton, Karen M.
Published: (2003)