Shearing Mechanisms and Complex Particle Growth in Nickel Superalloy 718
| Main Author: | |
|---|---|
| Language: | English |
| Published: |
The Ohio State University / OhioLINK
2016
|
| Subjects: | |
| Online Access: | http://rave.ohiolink.edu/etdc/view?acc_num=osu1461079188 |
| id |
ndltd-OhioLink-oai-etd.ohiolink.edu-osu1461079188 |
|---|---|
| record_format |
oai_dc |
| spelling |
ndltd-OhioLink-oai-etd.ohiolink.edu-osu14610791882021-08-03T06:35:46Z Shearing Mechanisms and Complex Particle Growth in Nickel Superalloy 718 McAllister, Donald P. Aerospace Materials Materials Science Metallurgy superalloy STEM EDS 718 deformation yield strength modeling electron microscopy microtwinning Ni3Nb particle growth morphology Alloy 718 is a γ''-strengthened Ni-base disk superalloy used in the aerospace industry, and it has been used prominently for decades. Though there has been extensive research into the processing/property relationships, there is very little known about the intermediate microstructure and mechanisms that are common in commercial 718 that dictate the yield strength. A variety of analytical techniques, including scanning transmission electron microscopy (STEM) and energy dispersive spectroscopy (EDS) were employed to investigate the microstructure of alloy 718 after various deformed conditions and heat treatment conditions.The γ'' in alloy 718 following a commercial heat treatment was found to have both monolithic γ'' particles as well as composite particles in which γ' and γ'' share a planar phase boundary. Isothermal heat treatments were applied to solutionized samples, and it was found that low heat treatment temperatures produced a large percentage of composite particles, but high temperatures led to the formation of a primarily monolithic structure. Additionally, these composite particles were shown to have a desirable stabilizing effect at high temperatures, and they were seen to grow much more slowly than their monolithic counterparts. STEM analysis was able easily show the morphology of any edge-on γ'' particles, and EDS was capable of determining the general morphology of in-plane particles. EDS was also useful in determining a rough volume fraction of each phase in tin foils, and it was found that the volume fraction of γ' was slightly larger than that of γ'' after commercial heat treatments.Deformation mechanisms were also characterized using STEM. Diffraction STEM was used on isolated dislocations and it was determined that isolated dislocations do not have contrast consistent with 1/2<110> dislocations, so some form of <112> dislocation was thought to be operative. Atomic resolution STEM analysis uncovered a variety of mechanisms present in tensile samples. Deformation at 22°C was found to occur primarily through the isolated shearing of γ'' into an ISF configuration while the surrounding matrix is left without a fault by a partial loop forming at the γ''/matrix interface. At 427°C, stacking faults were seen extending into the matrix, and isolate microtwins began to form in the γ'' phase. At 649°C, microtwins began to extend through the matrix and across large portions of the grain. The partials forming the microtwins are of multiple Burgers vector values, but they do not shear in a regular pattern. This indicates that the microtwin formation is likely assisted by localized reordering in the both the γ' and γ'' phases. Even so, there was no evidence found for segregation of elements to faults or twins.The understanding gained through this research has been used to inform precipitation and growth models. The precipitation and growth models will be combined with mechanistically-accurate yield strength models to improve predictions localized properties after a desired heat treatment. 2016-08-08 English text The Ohio State University / OhioLINK http://rave.ohiolink.edu/etdc/view?acc_num=osu1461079188 http://rave.ohiolink.edu/etdc/view?acc_num=osu1461079188 unrestricted This thesis or dissertation is protected by copyright: all rights reserved. It may not be copied or redistributed beyond the terms of applicable copyright laws. |
| collection |
NDLTD |
| language |
English |
| sources |
NDLTD |
| topic |
Aerospace Materials Materials Science Metallurgy superalloy STEM EDS 718 deformation yield strength modeling electron microscopy microtwinning Ni3Nb particle growth morphology |
| spellingShingle |
Aerospace Materials Materials Science Metallurgy superalloy STEM EDS 718 deformation yield strength modeling electron microscopy microtwinning Ni3Nb particle growth morphology McAllister, Donald P. Shearing Mechanisms and Complex Particle Growth in Nickel Superalloy 718 |
| author |
McAllister, Donald P. |
| author_facet |
McAllister, Donald P. |
| author_sort |
McAllister, Donald P. |
| title |
Shearing Mechanisms and Complex Particle Growth in Nickel Superalloy 718 |
| title_short |
Shearing Mechanisms and Complex Particle Growth in Nickel Superalloy 718 |
| title_full |
Shearing Mechanisms and Complex Particle Growth in Nickel Superalloy 718 |
| title_fullStr |
Shearing Mechanisms and Complex Particle Growth in Nickel Superalloy 718 |
| title_full_unstemmed |
Shearing Mechanisms and Complex Particle Growth in Nickel Superalloy 718 |
| title_sort |
shearing mechanisms and complex particle growth in nickel superalloy 718 |
| publisher |
The Ohio State University / OhioLINK |
| publishDate |
2016 |
| url |
http://rave.ohiolink.edu/etdc/view?acc_num=osu1461079188 |
| work_keys_str_mv |
AT mcallisterdonaldp shearingmechanismsandcomplexparticlegrowthinnickelsuperalloy718 |
| _version_ |
1719439711170199552 |