The Effects of Aspect Ratio of the Primarily Deformation Zone on Load and Material Flow in the Injection Upsetting

The Effects of Aspect Ratio of the Primarily Deformation Zone on Load and Material Flow in the Injection Upsetting

Bibliographic Details
Main Author:	Editörden
Format:	Article
Language:	English
Published:	Bursa Uludag University 2004-08-01
Series:	Uludağ University Journal of The Faculty of Engineering
Online Access:	http://mmfdergi.uludag.edu.tr/article/view/5000082666

Similar Items

The investigation in the deformation of anisotropy for upsetting of ring
by: Yen-Ti Lin, et al.
Published: (2010)

Analysis of deformation behaviours in upsetting processes
by: HUANG,DE-FU, et al.
Published: (1991)

Study on the hot injection upsetting process
by: Liao Chun-Chi, et al.
Published: (1995)

Investigation into upset and upset recovery using bifurcation analysis
by: Gill, Stephen J.
Published: (2014)

Study on deformation behaviours of square block in upsetting process by energy method
by: 何惠琳
Published: (1992)

Deformation in the high speed upsetting of rings : a solution by weighted residuals
by: Ravindranath, Thangavelu
Published: (1976)

Simulation and Experiment of Electrical Upsetting Process with Intelligent Control Load
by: Wei-Jhe Hong, et al.
Published: (2012)

Influence of the amount of deformation on the change in the porosity of sinters subjected to free cold upsetting
by: Rosiak Mariusz, et al.
Published: (2017-01-01)

The size effect for ring upsetting forging
by: Chiao-yuan Hsiao, et al.
Published: (2012)

Averaging level control in the presence of frequent inlet flow upsets
by: Rosander, Peter
Published: (2012)

Deformation Behavior and Microstructural Evolution of T-Shape Upsetting Test in Ultrafine-Grained Pure Copper
by: Hongpeng Jiang, et al.
Published: (2021-08-01)

Trickle flow multiple hydrodynamic states : the effect of flow history, surface tension and transient upsets
by: Van der Westhuizen, Ina
Published: (2013)

The effect of upsetting ratio on mechanical properties for hydromechanically bulged axisymmetric components made from copper tubes
by: T. Miłek
Published: (2017-01-01)

Primarily Thai
by: Phatthanodom, Fahmui
Published: (1998)

The influence of strain rate and the effect of friction on the forging load in simple upsetting and closed die forging
by: Klemz, Frances Bland
Published: (1984)

Cross wedge rolling with upsetting
by: Tofil A., et al.
Published: (2013-12-01)

Milk Upsets My Stomach
by: Farrell, Vanessa A.
Published: (2011)

Upsetting of hollow flanged components
by: Shahmoradi, Seyed Abbas
Published: (1981)

The effect to the friction contact interface for upsetting forging
by: Chein-pang Lin, et al.
Published: (2009)

Generation of a Layer of Severe Plastic Deformation near Friction Surfaces in Upsetting of Steel Specimens
by: Sergei Alexandrov, et al.
Published: (2018-01-01)

ON HEAT-SHARING RATIO IN DEFORMATION ZONE UNDER CUTTING
by: Flora A. Vistoropskaya, et al.
Published: (2018-07-01)

ON HEAT-SHARING RATIO IN DEFORMATION ZONE UNDER CUTTING
by: Flora A. Vistoropskaya, et al.
Published: (2012-10-01)

Effect of surface topography of die on friction for micro upsetting
by: Ching-Chung Mao, et al.
Published: (2005)

Upset Paths and 2-Majority Tournaments
by: Alshaikh, Rana Ali
Published: (2016)

Experimental Research and Method for Calculation of 'Upsetting-with-Buckling' Load at the Impression-Free (Dieless) Preforming of Workpiece
by: Kukhar Volodymir, et al.
Published: (2018-01-01)

Novel Quadruple Cross-Coupled Memory Cell Designs With Protection Against Single Event Upsets and Double-Node Upsets
by: Aibin Yan, et al.
Published: (2019-01-01)

Material and Structural Modeling Aspects of Brain Tissue Deformation under Dynamic Loads
by: Monika Ratajczak, et al.
Published: (2019-01-01)

Investigation on upsetting assisted by low-frequency vibration
by: Zhang M., et al.
Published: (2015-01-01)

Upset in Response to a Sibling’s Partner’s Infidelity
by: Dafni Hellstrand, et al.
Published: (2015-08-01)

Upsetting the dogma: germline selection in human males.
by: James F Crow
Published: (2012-01-01)

Steel balls forming by cross rolling with upsetting
by: Z. Pater, et al.
Published: (2013-01-01)

Upsetting with Conical Dies for Metal Sputtering Targets
by: Wun-Sin Wang, et al.
Published: (2011)

The application of Meshless Method in Aluminum Upsetting Process
by: LIN, TSUNG-WEI, et al.
Published: (2018)

A Study of Friction Phenomenon of Upsetting Process
by: KUO,YUNG-CHIH, et al.
Published: (2019)

UPSET RECOVERY TRAINING FOR CIVIL AVIATION PILOTS
by: V. S. Degtyarev, et al.
Published: (2021-02-01)

The educational inclusion of the students with upsets of the oral communication
by: Merling Murguia Moré, et al.
Published: (2015-09-01)

Inverse Problem Research in Upsetting Parameters Estimation
by: Chen Chun Kung, et al.
Published: (2001)

Crack initiation kinetics in upset cylindrical samples
by: Maxim S. Yegorov, et al.
Published: (2017-10-01)

Build Rings Upsetting Friction Model by RSM
by: Jung-Te Chu, et al.
Published: (2012)

A Realistic Friction Modeling in Simple Upsetting
by: Chung-Hung Lee, et al.