The Mechanism of Position-Mode Side Guide in Correcting Camber in Roughing Process of a Hot Strip Mill

by Han-Kai Hsu, Jong-Ning Aoh
Published 2019-04-01

Effect of Clearances in Mill Stands on Strip End Motion During Finishing Rolling

by Han-Kai Hsu, Jong-Ning Aoh
Published 2019-06-01

Friction Stir Processing of Copper-Coated SiC Particulate-Reinforced Aluminum Matrix Composite

by Chih-Wei Huang, Jong-Ning Aoh
Published 2018-04-01

Description of Residual Stresses in Autofrettaged Open-Ended Cylinders Made of High-Strength Steel

by Sergei Alexandrov, Elena Lyamina, Jong-Ning Aoh, Yeau-Ren Jeng
Published 2020-06-01

The Strengthening Mechanism of Adding Copper-Coated SiC Particles Aluminum-Matrix Composites by Friction Stir Processing

by 黃智威
Published 2019

Study on strip end flip phenomenon during finishing rolling in hot rolling process

by Han-Kai Hsu, 許涵剴
Published 2019

Hot Embossing on Metallic Submicron Structures

by Cheng-Hui Hung, 洪正輝
Published 2006

In-Plane Residual Stress Analysis by Using Combination of Moir Interferometry and Blind Hole-Drilling Method

by Jian-Ying Lee, 李建瑩
Published 2006

FEM Analysis on the Sizing Press Process and the Subsequent Horizontal Rolling Process of Steel Slab

by Zong-san You, 游宗翰
Published 2006

Characterization of Weld and Analysis of Welding Mechanisms of Friction Stir Welding(FSW) on Aluminum Alloy

by Din-wei Lin, 林鼎崴
Published 2006

The Study of the Weldability of TMCP Steel under Higher Heat Input

by Kung-Sheng Lai, 賴耿賢
Published 2000

Surface Oxidation Characteristics of Co- and Ni-based Clad Layers Deposited by High Energy Beams

by Sheng-An Tsai, 蔡盛安
Published 2000

The Fabrication of Micro/Nano-Sclae Gratings on Metal/PMMA Stack Layer using Direct Micro/Nanoimprint

by Tsung-Ching Chou, 周仲鯨
Published 2010

Analysis on Flow Behavior and Mechanical property of Lap Joint Friction Stir Weld of Aluminum-Clad 2024-T3 Aluminum Alloy Sheets

by Chih Wei, 黃智威
Published 2010

Two Dimensional Displacement Field Measurement using ESPI and Phase Shifting Interferometry for Hole-Drilling Method

by Tai-Hsin Liu, 劉岱鑫
Published 2010

電子光斑干涉術結合數位影像相關法之平板面內應力場分析

by Shou-Wei Chen, 陳守為
Published 2013

Study on Simulation and Microstructure of Ti-6Al-4V alloy in Upset Forging Process

by Cho-Wei Lin, 林哲偉
Published 2002

添加微米AlNp對AM60鎂合金熱傳導特性之研究

by LIN, SHIH-PIN, 林世斌
Published 2012

利用旋轉施力機構配合電子光斑干涉術結合數位影像相關法之平板面內位移場分析

by Yu-Hsun Lin, 林郁勳
Published 2014

鋼胚熱軋製程二維非對稱性軋延之模擬分析

by Kai-Hong Lien, 連凱泓
Published 2014